Contents

Installing

This chapter puts Fernbedienung on an M-VAVE FM-1 and takes it off again. You install from a web page in Chrome or Edge on a computer, not on the iPad or iPhone, and you can go back to M-VAVE's official firmware the same way. If an install goes wrong, see If something goes wrong.

What you need

# Item Why
1 An M-VAVE FM-1, charged It runs on its battery while the firmware is written.
2 A computer with Chrome or Edge The installer needs Web MIDI. Safari, Firefox, iPad and iPhone don't have it.
3 A USB data cable Charge-only cables don't carry data. Plug it straight into the computer, not into a hub.
4 Steckfeld SF1 1.4.0 on the iPad or iPhone Fernbedienung 1.0 is built for this version. See Versions.

Fernbedienung is unofficial firmware, provided as is and without any warranty (GPL-3.0). It is not made, endorsed or supported by M-VAVE or teenage engineering. A failed or interrupted install can leave the FM-1 unable to start until it is recovered with a USB tool. You can go back to the official firmware at any time.

Install Fernbedienung

  1. Close every app on the computer that uses MIDI: DAWs, M-UPGRADE, editors.
  2. Connect the FM-1 to the computer and switch it on.
  3. Open the installer from the Fernbedienung page on steckfeld.app (Open the installer). It opens with Fernbedienung already picked under Firmware.
  4. Press Install. When the browser asks for MIDI access, allow it.
  5. Wait until the status line says Done. Don't unplug the cable and don't close the page before that. The page keeps the computer awake by itself while it writes.
  6. Unplug the FM-1 from the computer and connect it to the iPad or iPhone. See Connecting.

During the write the FM-1 shows the update screen described in The update screen. When it is done, the FM-1 restarts and shows FERNBEDIENUNG with the version number for about a second.

The installer works over M-VAVE's official firmware V15 and over other community firmware that uses the same install protocol.

The Fernbedienung README also points to the FM-1 Firmware Hub (thefirmwarehub.com) as a second place to install from.

What the status line says

# Status What it means
1 Connect the FM-1 and press Install. The page is ready.
2 Loading the package… The page downloads the firmware and checks that it arrived intact.
3 Talking to the FM-1… The page found the FM-1 and is starting.
4 The FM-1 checks the package… The FM-1 checks the firmware before anything is written.
5 Switching to update mode… The FM-1 restarts into update mode.
6 Writing… do not unplug The firmware is being written.
7 Restarting… The write is finished and the FM-1 restarts.
8 Done: followed by the firmware's id The FM-1 came back and reports the package that was written.

The Detailed log under the progress bar lists every step with a time stamp. Copy it if you need to report a problem.

The update screen

While the firmware is written, the FM-1 shows the sign of Elektro Kabelmaier, the electronics shop inside Steckfeld SF1: ELEKTRO KABELMAIER in yellow on blue, a yellow strip with +++ FIRMWARE-UPDATE +++, the name of the firmware being written and a rotating bar next to Bitte nicht ausstecken! ("please don't unplug").

The screen stays up until the write is finished. If the cable comes out in the middle, the FM-1 stays in update mode; reconnect it and press Install again, and the write picks up where it stopped.

Update to a newer version

Install the new version the same way, over the one you have. Your FM-1 settings (MIDI channel, velocity, OPEN) should still be there afterwards. If they aren't, set them again on the EDIT page.

Each Fernbedienung version goes with one Steckfeld SF1 version. Update both, or the FM-1 says UPDATE NEEDED. See Versions.

Go back to the official firmware

The installer can write M-VAVE's FM-1 V15 back. It only accepts the unmodified official file, and the file never leaves your browser.

  1. Download FM-1 V15 from m-vave.com/download (Downloads → PC Firmware).
  2. Open the installer and scroll to Back to the official firmware.
  3. Choose the downloaded file. The status line says That is the official FM-1 V15. Ready to write. If it says That is not the official FM-1 V15 file., you picked the wrong file.
  4. Press Write the official V15 and wait until it says Done: the FM-1 started with its official firmware.

Versions

# Fernbedienung Steckfeld SF1 Protocol
1 1.0 1.4.0 1

The FM-1 and Steckfeld SF1 check each other's protocol version when they connect. If they differ, the FM-1 shows UPDATE NEEDED and tells you which side to update. See Screens.

Fernbedienung 1.0 was tested on an FM-1 with an iPad. The product page lists most features as "testing": built, but not yet confirmed on hardware in every case. Using it with an iPhone has not been tested.

If something goes wrong

# What you see What to do
1 This browser has no Web MIDI. Open the page in Chrome or Edge. Use Chrome or Edge on a computer.
2 MIDI (SysEx) access was not allowed. Allow MIDI in the site settings (the icon in the address bar) and press the button again.
3 FM-1 not found. Check the cable and close other MIDI apps. Use a data cable without a hub, switch the FM-1 on, quit DAWs, M-UPGRADE and editors.
4 The USB connection was lost. Reconnect and press Install again.
5 The write stopped. Reconnect the FM-1 and press Install again. Do that. The FM-1 stays in update mode until the write is finished.
6 The FM-1 in update mode did not appear. Replug the cable and press Install again.
7 The FM-1 did not come back after the write. Power-cycle it. Switch the FM-1 off and on.
8 The FM-1 is in another firmware's update mode. Finish that install with that firmware's own updater first.
9 The package on the site is damaged (SHA-256 mismatch). Reload the page. Reload. If it keeps happening, the file on the server is broken.
10 The connected device is not an FM-1 Unplug other MIDI devices and connect only the FM-1.

If the firmware doesn't start after an install, the FM-1 opens FM-1 USB RESCUE by itself after two failed starts in a row. You can also open it by holding OCT− while you switch the FM-1 on. The rescue screen says CONNECT USB and OPEN THE INSTALLER; the installer works there as usual. There is no sound in rescue mode.

If the power runs out during a write, the FM-1 may stay dark and not show up as a USB device. Charge it, then install again. An FM-1 that doesn't start at all can be recovered with MvaveFM1Unbricker (github.com/Quixotic7/MvaveFM1Unbricker). See Start a recovery mode by hand.