Troubleshooting
This chapter lists problems you may run into with the FM-1 and Steckfeld SF1, and what to do about them. Install problems are in Installing. The FM-1's recovery modes are in Advanced.
Connection
| # | Problem | What to do |
|---|---|---|
| 1 | The FM-1 says No USB connection. | Check the cable and the port. Use a USB-C data cable, not a charge-only one. |
| 2 | The FM-1 says Steckfeld not connected. | Open Steckfeld SF1. If it is already open, unplug the FM-1 and plug it in again: Steckfeld asks who is there whenever a MIDI device comes or goes. |
| 3 | The FM-1 says UPDATE NEEDED. | The FM-1 and Steckfeld use different protocol versions. Update the side the screen names. See Screens. |
| 4 | The FM-1 showed Steckfeld and went back to waiting. | The USB connection dropped, or Steckfeld was closed. Reconnect or open Steckfeld; the FM-1 picks up again by itself. |
Keys and knobs
| # | Problem | What to do |
|---|---|---|
| 1 | The keys play nothing. | The patch needs a MIDI In part, listening on the FM-1's MIDI channel or on ALL. Check the channel on the FM-1's EDIT page. |
| 2 | The knobs and buttons don't reach Steckfeld. | The EDIT page or the system settings may be open. Press EDIT (or HOME) to close them. |
| 3 | A knob does nothing. | Its tile is empty: the page has fewer than four values. Turn SELECT to another page. |
| 4 | ALGORITHM does nothing. | It only works on Route (cables) and in a sequencer's Edit screen (steps). |
| 5 | REC or SAVE does nothing. | Look at the footer. If no label stands next to the button, it has no job on this page. |
| 6 | REC did something other than the footer's page action. | A notice was showing. REC does the notice's action first. See Screens. |
| 7 | A part button is dark and does nothing. | The bay has no part of that kind. |
| 8 | The patch list closed without loading. | Any control other than PRESETS, SELECT, REC, the keys and the octave buttons closes it. Turn PRESETS to open it again. |
| 9 | PLAY doesn't start Steckfeld, and the footer says Clock: external. | Steckfeld follows an external MIDI clock. Start and stop from the device that sends the clock. |
| 10 | Notes are an octave off. | OCT− or OCT+ is lit. Press the other one until neither is lit. |
Sound
| # | Problem | What to do |
|---|---|---|
| 1 | No sound from the FM-1, and the footer says Sound on iPad or Sound on another device. | Press REC (use FM-1). |
| 2 | No sound, and the footer says USB audio Off. | iOS isn't playing to the FM-1. Pick the FM-1 as Steckfeld's output. |
| 3 | No sound, and USB audio says On. | Turn MASTER up. All the way down is silence. |
| 4 | A short gap in the sound after leaving the EDIT page. | Storing the settings interrupts the sound for a moment. Change settings while nothing plays. |
Screen
| # | Problem | What to do |
|---|---|---|
| 1 | The picture area is empty for a part. | ДАМП, 曲げ MAGE, SCHLIERE and COMBINÉ have no picture in Fernbedienung 1.0. The knobs and tiles still work. |
| 2 | The screen is red, or blue, when you expect the other. | Check THEME in the system settings (hold HOME, press EDIT). With SYNC the FM-1 follows Steckfeld's appearance, and stays blue until Steckfeld is connected. |
| 3 | The screen shows UBOOT IN and a number. | You are holding OCT− and OCT+ together. Let go before the count ends, or the FM-1 switches to UBOOT. If that happens, switch it off and on. |
The FM-1 doesn't start
After two failed starts in a row, the FM-1 opens FM-1 USB RESCUE by itself. You can also open it by holding OCT− while you switch the FM-1 on. Connect it to a computer and install Fernbedienung again with the installer. See Installing.
Advanced
For when you know the basics. You don't need this to get started.
Start a recovery mode by hand
| # | Mode | How to start it | What it is for |
|---|---|---|---|
| 1 | USB RESCUE | Hold OCT− while you switch the FM-1 on. It also starts by itself after two failed starts in a row. | Installing Fernbedienung again with the installer when the firmware doesn't start. There is no sound. |
| 2 | UBOOT | While the firmware runs, hold OCT− and OCT+ together for 5 seconds. After 2 seconds the screen counts down UBOOT IN. | Recovery tools such as MvaveFM1Unbricker. |
Let go of OCT− and OCT+ before the countdown ends if you didn't mean to start UBOOT.
If USB RESCUE shows UNKNOWN FLASH instead of OPEN THE INSTALLER, the installer can't write from there. Use a recovery tool.
If the FM-1 freezes or shows a crash screen
It restarts by itself, after about eight seconds if it froze. If it fails to start twice in a row, it opens USB RESCUE. Install Fernbedienung again from there.
Report a problem
Note the firmware version (the EDIT page's footer, or the start screen) and your Steckfeld SF1 version. For install problems, copy the installer's Detailed log.