Connecting to the OP-1 field
Beiwagen works with a teenage engineering OP-1 field and one USB cable between the two. The OP-1 sends its four tape tracks to the FM-1, records what the FM-1 sends back, and receives notes from the FM-1's keys. This chapter covers the cable, the OP-1's settings and how to tell the connection works. What has been tested on real hardware is listed in What is tested.
Plug in
- Connect the FM-1 to the OP-1 field with a USB data cable.
- Switch both on.
- On the OP-1, set USB audio to mode 8 (tape tracks 1 to 4, stereo each).
- On the OP-1, set MIDI to receive notes, not only to send them. Otherwise the FM-1's keys play nothing.
The FM-1 shows up on the USB bus as Beiwagen FM-1.
Check the connection
| # | Where | What you see when it works |
|---|---|---|
| 1 | Footer, right | No OP-1 in amber disappears once the OP-1 streams audio to the FM-1. |
| 2 | HOME, Tracks | A level bar moves at the foot of each track tile while the OP-1's tape plays. |
| 3 | HOME, USB | CH 8 and PAIRS 4, a packet count under PKT/S that keeps going, and eight meters that move. |
| 4 | OP-1 | Its USB input carries the FM-1's output. |
The USB page is described in USB.
Where the sound goes
| # | Direction | What travels |
|---|---|---|
| 1 | OP-1 → FM-1 | The four tape tracks, each as a stereo pair. |
| 2 | FM-1 → OP-1 | One stereo signal: the FM-1's mix, after the MASTER knob. It arrives as the OP-1's USB input. |
| 3 | FM-1 → its own output | The same mix. |
| 4 | FM-1 keys → OP-1 | Notes over USB-MIDI, plus the sequencer's and the arpeggiator's notes. |
| 5 | OP-1 → FM-1 | MIDI clock, start and stop, if the OP-1 sends them. The sequencer can follow them. |
The OP-1 puts its USB input on the track that is selected on the OP-1, together with whatever you play live. That track also comes back to the FM-1 as one of the four pairs. If the FM-1 mixes it in again, the signal goes round in a loop. Before you record, let the FM-1 find that track and keep it out of the mix: see Find the return track.
What is tested
Beiwagen 0.2 is the first release. Some of it ran on an FM-1 with an OP-1 field (firmware 1.7.3), some of it is built but has not run on the hardware yet.
| # | Feature | Status |
|---|---|---|
| 1 | Four tape tracks from the OP-1 in USB mode 8 | Tested on an FM-1 |
| 2 | Audio from the FM-1 back to the OP-1 as its USB input | Tested on an FM-1 |
| 3 | The FM-1's keys play the OP-1 over USB-MIDI | Tested on an FM-1 |
| 4 | Mixer with filter and drive per track, delay and reverb sends | Built, not tested on an FM-1 |
| 5 | Finding the return track with REC | Built, not tested on an FM-1 |
| 6 | Sequencer and arpeggiator | Built, not tested on an FM-1 |
| 7 | Presets and patterns on the keys, the saved session | Built, not tested on an FM-1 |
| 8 | System settings (button lights) | Built, not tested on an FM-1 |
| 9 | Modulation (LFO, ENV) | Planned |