Sequencer and arpeggiator
Beiwagen has a step sequencer and an arpeggiator. Both play the OP-1 over USB-MIDI, at their own tempo or following the OP-1's MIDI clock. Press SEQ for the sequencer and ARP for the arpeggiator. Both are built but have not been tested on an FM-1 yet.
Patterns
The sequencer holds 27 patterns, one per key. A pattern has 1 to 32 steps, each a 16th note, and its own MIDI channel and swing. A step is either off or plays one note with a velocity and a gate length.
A new pattern has 16 steps, all off, on MIDI channel 1, without swing.
Sequencer pages
The sequencer has four pages: Steps, Step, Pattern and Clock.
| # | Page | KNOB1 | KNOB2 | KNOB3 | KNOB4 |
|---|---|---|---|---|---|
| 1 | Steps | Step | Note | Velocity | Gate |
| 2 | Step | Step | Note | Velocity | Gate |
| 3 | Pattern | Pattern | Length | MIDI ch | Swing |
| 4 | Clock | BPM | Sync | Clock out |
Steps and Step edit the same thing. Steps shows the pattern as a roll, Step shows the selected step's values as large tiles.
The header
The right side of the header shows, from left to right:
| # | Item | Meaning |
|---|---|---|
| 1 | P1 … P27 | The selected pattern. |
| 2 | Green triangle | Playing. |
| 3 | Two amber bars | Armed: waits for the OP-1's MIDI clock to start. |
| 4 | Grey square | Stopped. |
| 5 | EXT | The tempo comes from incoming MIDI clock. |
| 6 | Number | The tempo in BPM. With MIDI clock it is measured; -- until it can be. |
| 7 | Red square | Recording is on. |
| 8 | ARP | The arpeggiator is on. |
The same header shows in the arpeggiator's pages.
Steps page
The roll shows 16 steps side by side: the 16 that contain the selected step. Pitch goes up. Each step's note is a block whose width is its gate and whose brightness is its velocity. A tied step fills its whole column. Thin lines mark the Cs, and every fourth step has a brighter mark at the top.
The selected step has a lighter background and a blue bar at the bottom. While the pattern plays, the current step's mark and note turn orange. Steps past the pattern's length are black.
Under the roll, a line in the knobs' colours shows the selected step: its number and the pattern length (for example 5/16), the note or Off, the velocity and the gate.
The visible note range follows the notes on screen: at least an octave, and as many notes as still fit.
Edit steps
| # | Control | What it does |
|---|---|---|
| 1 | KNOB1 Step | Selects a step, from 1 to the pattern's length. |
| 2 | KNOB2 Note | Sets the step's note and switches the step on. |
| 3 | KNOB3 Velocity | Sets the step's velocity (1 to 127) and switches the step on. |
| 4 | KNOB4 Gate | How long the note plays, 1 to 100 % of the step. One more detent past 100 % is Tie. |
| 5 | EDIT | Switches the selected step on or off. Its note stays, so switching it on again brings it back. |
| 6 | A key | Puts the key's note into the selected step at the keyboard's velocity, switches it on and selects the next step. After the last step it goes back to step 1. |
A tied step holds its note into the next step. If the next step plays the same note, the note just continues. Otherwise it ends where the next step starts.
The keys also play the OP-1 while you enter steps, so you hear what goes in.
Pattern page
| # | Parameter | Range | What it does |
|---|---|---|---|
| 1 | Pattern | 1 to 27 | The pattern to edit and play. While the sequencer plays, the new pattern starts when the current one reaches its end. |
| 2 | Length | 1 to 32 | Steps in the pattern. |
| 3 | MIDI ch | 1 to 16 | The channel the pattern plays on. Separate from the keyboard's channel. |
| 4 | Swing | 50 to 75 % | Delays every second step. 50 % is straight, about 67 % is a triplet feel, 75 % is the strongest. |
Clock page
| # | Parameter | Range | Default | What it does |
|---|---|---|---|---|
| 1 | BPM | 30 to 300 | 120 | The tempo when no MIDI clock comes in. |
| 2 | Sync | Auto, Internal | Auto | Auto follows MIDI clock as soon as it arrives. Internal ignores it. |
| 3 | Clock out | Off, On | Off | On sends MIDI start, clock and stop to the OP-1 while the sequencer plays on its own tempo. |
Play and stop
PLAY works from every section.
Without incoming MIDI clock, PLAY starts the selected pattern from step 1, and stops it again. PLAY is lit while the pattern plays.
With Sync on Auto and MIDI clock coming in from the OP-1, PLAY arms the sequencer instead. PLAY blinks and the header shows two amber bars. The pattern then plays whenever the OP-1's clock runs: it starts with the OP-1's start, continues from where it stopped with the OP-1's continue, and stops with its stop. If the clock is already running when you press PLAY, the pattern joins at the next step. Press PLAY again to disarm.
If the clock stops arriving for half a second, the sequencer goes back to its own tempo, stopped and disarmed.
Record
- Open the sequencer and press REC. REC lights up and the footer says REC recording.
- Press PLAY.
- Play the keys. Each note goes into the step it is closest to, with the keyboard's velocity. How long you hold the key becomes the step's gate.
- Press REC in the sequencer again to stop recording.
A key played a little early goes into the next step, and that step doesn't play again on this pass, because you already played it. Recording writes into the pattern that is playing.
Recording stays on when you leave the sequencer, and keys still go into the playing pattern. Outside the sequencer REC looks for the return track instead, so go back to SEQ to switch recording off. When the sequencer is stopped, recording records nothing and the keys enter steps as usual.
Arpeggiator
Press ARP to open the arpeggiator's pages, and press ARP again there to switch it on or off. While it is on, the keys you hold go to the arpeggiator instead of sounding directly, in every section. It plays on the keyboard's MIDI channel, with each note's velocity as you played it, at the sequencer's tempo or the incoming MIDI clock.
Arp page
| # | Parameter | Choices | Default | What it does |
|---|---|---|---|---|
| 1 | Mode | Up, Down, Up-down, Random, Played | Up | The order of the notes. Played keeps the order you pressed them in. |
| 2 | Rate | 1/4, 1/8, 1/8 T, 1/16, 1/16 T, 1/32, 1/32 T | 1/16 | Note length. T is a triplet. |
| 3 | Gate | 5 to 100 % | 50 % | How long each note sounds, as a share of the rate. |
| 4 | Octaves | 1 to 4 | 1 | How many octaves the pattern climbs before it starts over. |
Arp keys page
| # | Parameter | Choices | Default | What it does |
|---|---|---|---|---|
| 1 | Arp | Off, On | Off | The arpeggiator on or off. Same as pressing ARP in this section. |
| 2 | Latch | Off, On | Off | On keeps the arpeggio going after you let go of the keys. The next chord, played after all keys were up, replaces it. |
The arpeggiator holds up to 16 notes. While the sequencer plays, its first note waits for the next beat of its rate, so it stays in time with the pattern.
Advanced
For when you know the basics. You don't need this to get started. Skip to Presets and patterns
Keep more than one pattern after switching off
A saved session keeps only the pattern you are editing, and it comes back as pattern 1. The other patterns are lost when you switch off. To keep them:
- Select each pattern on the Pattern page.
- Hold SAVE and press a key to store it.
- After switching on, open SEQ, hold SEL and press the key to load it back.
Tempo, sync, clock out and the arpeggiator's settings are never stored. Set them again after switching on.
Switch channels and patterns while notes sound
You can change a pattern's MIDI channel, switch patterns, stop, or switch off the arpeggiator while notes sound. Every note still ends on the channel it started on, so nothing hangs on the OP-1.