Installing
This chapter puts Beiwagen on an M-VAVE FM-1 and takes it off again. You install from a web page in Chrome or Edge on a computer, and you can go back to M-VAVE's official firmware the same way. If an install goes wrong, see If something goes wrong.
What you need
| # | Item | Why |
|---|---|---|
| 1 | An M-VAVE FM-1, charged | It runs on its battery while the firmware is written. |
| 2 | A computer with Chrome or Edge | The installer needs Web MIDI. Safari, Firefox, iPad and iPhone don't have it. |
| 3 | A USB data cable | Charge-only cables don't carry data. Plug it straight into the computer, not into a hub. |
Beiwagen is unofficial firmware, provided as is and without any warranty (GPL-3.0). It is not made, endorsed or supported by M-VAVE or teenage engineering. A failed or interrupted install can leave the FM-1 unable to start until it is recovered with a USB tool. You can go back to the official firmware at any time.
Install Beiwagen
- Close every app on the computer that uses MIDI: DAWs, M-UPGRADE, editors.
- Connect the FM-1 to the computer and switch it on.
- Open the installer from the Beiwagen page (Install Beiwagen). It opens with Beiwagen already picked under Firmware.
- Press Install. When the browser asks for MIDI access, allow it.
- Wait until the status line says Done. Don't unplug the cable and don't close the page before that. The page keeps the computer awake by itself while it writes.
During the write the FM-1 shows an update screen with a spinner. When it is done, the FM-1 restarts and shows the Beiwagen logo with the version number in the top right corner for about a second.
The installer works over M-VAVE's official firmware and over other community firmware that uses the same install protocol.
What the status line says
| # | Status | What it means |
|---|---|---|
| 1 | Connect the FM-1 and press Install. | The page is ready. |
| 2 | Talking to the FM-1… | The page found the FM-1 and is starting. |
| 3 | The FM-1 checks the package… | The FM-1 checks the firmware before anything is written. |
| 4 | Switching to update mode… | The FM-1 restarts into update mode. |
| 5 | Writing… do not unplug | The firmware is being written. |
| 6 | Restarting… | The write is finished and the FM-1 restarts. |
| 7 | Done: … | Beiwagen is running. The line ends with the version the FM-1 reports. |
The errors and what to do about them are in Install errors.
Go back to the official firmware
The same page writes M-VAVE's official FM-1 V15.
- Download FM-1 V15 from m-vave.com/download (Downloads, then PC Firmware).
- On the installer page, under Back to the official firmware, choose the downloaded
.fwscfile. - The status line says That is the official FM-1 V15. Ready to write. If it says the file is not the official one, download it again.
- Press Write the official V15 and wait for Done: the FM-1 started with its official firmware.
The page only accepts the unmodified official file, and the file stays in your browser.
If something goes wrong
| # | What happened | What to do |
|---|---|---|
| 1 | The write stopped halfway | Reconnect the FM-1 and press Install again. The FM-1 stays in update mode until a write is finished, and the installer picks up from there. |
| 2 | Beiwagen doesn't start | After two failed starts in a row, the FM-1 opens FM-1 USB RESCUE by itself. You can also open it: hold OCT− while you switch the FM-1 on. The installer works from that screen. |
| 3 | The FM-1 stays dark and shows up as no USB device | The battery may have run out during the write. Charge it, then install again. |
| 4 | Nothing above helps | Recover the FM-1 with MvaveFM1Unbricker. See Start the ROM bootloader. |
Advanced
For when you know the basics. You don't need this to get started. Skip to Connecting to the OP-1 field
Open USB rescue by hand
Hold OCT− while you switch the FM-1 on. The screen reads FM-1 USB RESCUE, CONNECT USB, OPEN THE INSTALLER and AUDIO OFF. Connect it to the computer and install Beiwagen as usual. There is no sound in rescue mode.
If the screen reads UNKNOWN FLASH instead of OPEN THE INSTALLER, the installer can't write from there. Use a recovery tool such as MvaveFM1Unbricker.
Start the ROM bootloader
Recovery tools such as MvaveFM1Unbricker need the FM-1 in its ROM bootloader.
- While Beiwagen runs, hold OCT− and OCT+ together.
- After 2 seconds the screen counts down: UBOOT IN 3, 2, 1.
- Keep holding until the screen shows UBOOT, 5 seconds in all.
Let go before the count ends if you didn't mean to.