Mixer
Press GLO to open the mixer. It takes all four OP-1 tape tracks, gives each a level, a pan, a filter with drive and two sends, adds a shared delay and reverb, and sends one stereo mix back to the OP-1. The usual job is a bounce: tracks 1 to 3 with effects, recorded onto track 4. The mixer is built but has not been tested on an FM-1 yet.
Pages
The mixer has 11 pages. Turn SELECT to move through them.
| # | Page | KNOB1 | KNOB2 | KNOB3 | KNOB4 |
|---|---|---|---|---|---|
| 1 | Track 1 | Level | Pan | Delay | Reverb |
| 2 | Track 1 tone | Cutoff | Reso | Drive | Mode |
| 3 | Track 2 | Level | Pan | Delay | Reverb |
| 4 | Track 2 tone | Cutoff | Reso | Drive | Mode |
| 5 | Track 3 | Level | Pan | Delay | Reverb |
| 6 | Track 3 tone | Cutoff | Reso | Drive | Mode |
| 7 | Track 4 | Level | Pan | Delay | Reverb |
| 8 | Track 4 tone | Cutoff | Reso | Drive | Mode |
| 9 | Delay | Time | Feedback | Tone | Return |
| 10 | Reverb | Size | Decay | Damping | Return |
| 11 | Master | Master | Inserts |
The track overview in the header
On every mixer page the header's right side shows the four tracks as numbered boxes:
| # | Box | Meaning |
|---|---|---|
| 1 | White | In the mix, with signal. |
| 2 | Grey | In the mix, quiet. |
| 3 | Dark | Muted. |
| 4 | Amber | The return track, kept out of the mix. |
The track whose page you're on is underlined. While the return track is being searched, the boxes are replaced by Finding, and by Not found for 2 seconds after a search that failed.
Track pages
| # | Parameter | Range | Default | What it does |
|---|---|---|---|---|
| 1 | Level | Off, −52.8 to +6.0 dB | 0.0 dB | The track's level in the mix. 1.2 dB per detent. |
| 2 | Pan | 100 L to 100 R | C | Left and right balance. The middle leaves the track as it is; turned to one side, that side gets louder by 3 dB and the other fades out. |
| 3 | Delay | 0 to 100 % | 0 % | How much of the track goes to the delay. |
| 4 | Reverb | 0 to 100 % | 0 % | How much of the track goes to the reverb. |
The sends come after the level, so turning a track down also turns down what it sends. A muted track sends nothing.
Tone pages
Each track has a filter with drive in its path, before the level. It is off until you pick a mode.
| # | Parameter | Range | Default | What it does |
|---|---|---|---|---|
| 1 | Cutoff | 20 Hz to 20 kHz | 20 kHz | The filter's frequency. |
| 2 | Reso | 0 to 100 % | 0 % | Resonance. Near the top the filter starts to ring on its own. |
| 3 | Drive | 0 to 100 % | 0 % | Overdrives the filter's input. Quiet parts come up and loud parts flatten, so the level stays about the same. |
| 4 | Mode | Off, LP 12, LP 24, BP 12, BP 24, HP 12, HP 24, Notch 12, Notch 24 | Off | Low-pass, band-pass, high-pass or notch, at 12 or 24 dB per octave. Off takes the filter and its drive out. |
Changing the mode, cutoff, resonance or drive while the tape plays doesn't click.
Delay and reverb
One delay and one reverb, shared by all four tracks. They only get what the tracks send them, and their output joins the mix at the Return level.
| # | Page | Parameter | Range | Default |
|---|---|---|---|---|
| 1 | Delay | Time | 10 ms to 500 ms | about 374 ms |
| 2 | Delay | Feedback | 0 to 100 % | 42 % |
| 3 | Delay | Tone | 500 Hz to 20 kHz | about 6 kHz |
| 4 | Delay | Return | 0 to 100 % | 100 % |
| 5 | Reverb | Size | 0 to 100 % | 50 % |
| 6 | Reverb | Decay | 0.1 s to 30 s | about 1.2 s |
| 7 | Reverb | Damping | 0 to 100 % | 40 % |
| 8 | Reverb | Return | 0 to 100 % | 100 % |
Tone cuts the delay's highs on every repeat, so the repeats get darker as they fade. Decay is the time the reverb's tail takes to fall by 60 dB, whatever the size. Damping makes the highs fade faster than the rest. With Return at 0 % the effect stops and uses no CPU.
Both start silent: raise a track's Delay or Reverb send to hear them.
Master page
| # | Parameter | Range | Default | What it does |
|---|---|---|---|---|
| 1 | Master | Off, −52.8 to +6.0 dB | 0.0 dB | The mix's level, before the MASTER knob. |
| 2 | Inserts | 2x, 1x | 2x | 2x runs the track filters at twice the sample rate, 1x at the sample rate. 1x uses less CPU. |
The CPU load is in the footer. Switching Inserts fades the filters out and back in.
Mute a track
On a track's page (Track N or Track N tone), press GLO. The track is muted, or heard again if it was muted. On the Delay, Reverb and Master pages, GLO does nothing.
Mutes are part of a preset. The track overview on HOME shows them too.
Find the return track
The OP-1 records its USB input onto the track that is selected on the OP-1, and that track also comes back to the FM-1. If the mixer kept it in the mix, the signal would loop. So the mixer needs to know which track is the return, and leaves it out.
- On the OP-1, select the track you want to record the mix onto.
- On the FM-1, outside the sequencer, press REC.
- The mix fades out, a short burst of noise goes to the OP-1, and the mix fades back in. This takes about 1.5 seconds.
- If one track carried the noise back, it becomes the return track: amber on HOME and in the header, and the footer says REC mix to N. If none did, or more than one, nothing changes and the header shows Not found.
You hear the noise burst on the FM-1's output too, even with MASTER turned down. While the search runs, the delay and the reverb stop, and their tails are cut.
Press REC again whenever you select another track on the OP-1. The return track is not stored in presets or in the session, so after switching on, the footer says REC find return until you press REC.
Bounce tracks 1 to 3 onto track 4
- Put the parts on OP-1 tracks 1 to 3. Leave track 4 empty.
- On the OP-1, select track 4.
- On the FM-1, press REC once. Track 4 turns amber.
- Set levels, pans, filters and sends on the FM-1 while the tape plays.
- On the OP-1, rewind, start recording on track 4 and play the tape.