Contents

Troubleshooting

This chapter lists problems by what you see, with the likely cause and the fix. Installer messages are in Install errors.

The FM-1 receives no audio from the OP-1.

  1. Check that the cable carries data and is plugged in at both ends.
  2. On the OP-1, check that USB audio is in mode 8.
  3. Open HOME and turn SELECT to the USB page. If PKT/S stays at 0, the OP-1 isn't streaming.

The sound loops or howls when the OP-1 records

The track the OP-1 records onto comes back into the mix. Select that track on the OP-1, then press REC on the FM-1 outside the sequencer. See Find the return track. If the search fails, mute that track with GLO on its mixer page.

REC shows Not found

The search didn't hear its noise burst on exactly one track.

# Cause Fix
1 No audio is streaming See No OP-1 in the footer.
2 The OP-1 doesn't pass its USB input to the selected track Check the OP-1's input routing for the selected track, then press REC again.

The keys don't play the OP-1

# Cause Fix
1 The OP-1's MIDI only sends Set the OP-1's MIDI to receive notes.
2 The arpeggiator is on ARP shows in the sequencer's header. Open ARP and press ARP to switch it off.
3 SAVE or SEL is held Let go. While either is held the keys pick preset slots.
4 Wrong MIDI channel Set the channel on HOME's Keys page to one the OP-1 listens on.
5 The keys play out of range At octave −3 or +3 some keys fall outside the MIDI note range and send nothing. Use OCT− or OCT+.

No sound from the FM-1

  1. Turn up MASTER.
  2. In the mixer, open the Master page and check that Master is not Off.
  3. Check the track tiles on HOME: dark tracks are muted, the amber one is the return and is never in the mix.
  4. Check each track's Level and its tone page's Mode and Cutoff: a low-pass at a low cutoff can make a track nearly silent.

No delay or reverb

Both only hear what the tracks send them. Raise Delay or Reverb on a track's page, and check Return on the Delay or Reverb page.

The sequencer is armed and waits for the OP-1's MIDI clock to start. Start the OP-1's playback, or set Sync on the Clock page to Internal and press PLAY to run on Beiwagen's own tempo.

Recording doesn't stop

Outside the sequencer REC looks for the return track instead. Press SEQ, then REC.

Stop playback to save

Saving is refused while the sequencer plays. Press PLAY to stop, then save.

Settings are gone after switching on

Beiwagen does not save the session by itself. Hold SAVE for 2 seconds before you switch off. Patterns other than the one you edit, the tempo and the arpeggiator's settings are not part of the session: store patterns on keys. See What is stored where.

The CPU figure is high

The footer shows the processor load. Set Inserts on the mixer's Master page to 1x, mute tracks you don't use, set unused filters' Mode to Off, and turn Return on the Delay or Reverb page to 0 % if you don't use them.

The buttons are dark

Open the settings (hold HOME, press EDIT) and raise LIGHTS. FX, LFO and ENV are always dark because they have no function yet, and EDIT is dark outside the sequencer.

Install errors

# Message What to do
1 This browser has no Web MIDI. Open the page in Chrome or Edge. Use Chrome or Edge on a computer.
2 MIDI (SysEx) access was not allowed. Allow MIDI in the site settings (in the address bar) and press Install again.
3 FM-1 not found. Check the cable and close other MIDI apps. Use a data cable without a hub, close DAWs, M-UPGRADE and editors.
4 The connected device is not an FM-1: … Connect the FM-1, not another MIDI device.
5 The package on the site is damaged (SHA-256 mismatch). Reload the page. Reload the page and try again.
6 The firmware list did not load: … Check the internet connection and reload.
7 The USB connection was lost. Reconnect and press Install again. Reconnect and press Install again.
8 The write stopped. Reconnect the FM-1 and press Install again. Reconnect and press Install again. The FM-1 waits in update mode.
9 The FM-1 in update mode did not appear. Replug the cable and press Install again. Replug and press Install again.
10 The FM-1 did not come back after the write. Power-cycle it. Switch the FM-1 off and on.
11 Written, but the FM-1 reports another version: … Install again.
12 The FM-1 is in another firmware's update mode. Finish that install with that firmware's own updater first.
13 That is not the official FM-1 V15 file. Download V15 from m-vave.com again and pick that file.

If the FM-1 doesn't start after an install, see If something goes wrong.