Contents

Controls and screen

This chapter lists what every button, knob and key on the FM-1 does in Beiwagen, the button combinations, and how the screen is laid out. Beiwagen is organised in four sections (HOME, mixer, sequencer, arpeggiator). Each has its own button and a few pages, and the four knobs under the screen always change what the current page shows.

The screen

Most pages share one layout:

# Area What it shows
1 Header The page's name on the left. On the right, either a dot per page of the section (the current one bright) or the section's own status: the track overview in the mixer, the transport in the sequencer and arpeggiator.
2 Four tiles One per knob, KNOB1 top left, KNOB2 top right, KNOB3 bottom left, KNOB4 bottom right. Each shows the parameter's name, its value in large type and a bar. The coloured line along the top of a tile is the knob's colour: blue, green, white, orange, as on the OP-1.
3 Footer On the left, what REC does right now. On the right, No OP-1 when no audio arrives, and the CPU load. Short messages (saved, loaded, errors) show here for a moment.

A tile fills with its knob's colour while you turn the knob and for about a second after. A tile without a parameter stays empty. Some pages use the whole area differently: the track overview, the step view of the sequencer, the USB page and the scope.

The footer's REC text

# Footer Meaning
1 REC find return No return track is set. REC looks for it.
2 REC mix to 4 Track 4 is the return track (the number varies). REC looks for it again.
3 REC record In the sequencer: REC switches recording on.
4 REC recording In the sequencer: recording is on. The REC label turns red.

Buttons

# Button What it does
1 HOME Opens HOME: track overview, keyboard settings, USB diagnostics, scope. See HOME.
2 GLO Opens the mixer. Pressed again on a track's page, it mutes that track or brings it back. See Mixer.
3 SEQ Opens the sequencer. See Sequencer.
4 ARP Opens the arpeggiator. Pressed again while you're there, it switches the arpeggiator on or off. See Arpeggiator.
5 PLAY Starts and stops the sequencer, from any section. When MIDI clock comes in, it arms the sequencer instead. See Play and stop.
6 REC In the sequencer: recording on or off. Everywhere else: finds the return track. See Find the return track.
7 EDIT In the sequencer: switches the selected step on or off. Elsewhere it does nothing on its own and stays unlit.
8 SAVE Hold and press a key: stores the mixer as a preset on that key (in the sequencer: the pattern). Hold alone for 2 seconds: saves the session. See Presets and patterns.
9 SEL Hold and press a key: loads the preset from that key (in the sequencer: the pattern).
10 OCT− / OCT+ Moves the keyboard down or up an octave, three each way. OCT− is lit while the keyboard is below its home octave, OCT+ while it is above.
11 FX, LFO, ENV No function yet. They stay unlit.

The section buttons light up to show which section is open. Each section remembers the page you were on.

Knobs

# Knob What it does
1 SELECT Steps through the pages of the current section. It stops at the first and the last page.
2 KNOB1–KNOB4 Change the parameter on the matching tile.
3 MASTER Output level. It sets what you hear and what goes back to the OP-1. Fully down is silence.
4 ALGORITHM Changes a value in the system settings. No function otherwise.
5 PRESETS No function.

Each detent moves a parameter by one step. On the mixer, a full sweep from one end to the other takes 50 detents, and a level moves 1.2 dB per detent.

Keys

The 27 keys send notes to the OP-1 over USB-MIDI. At the home octave the lowest key plays F3 and the highest G5 (middle C is C4). The MIDI channel and the velocity are set on HOME's Keys page.

The keys do more in some situations:

# Situation What a key does
1 SAVE or SEL held Picks a preset or pattern slot. The key doesn't play a note.
2 Arpeggiator on Adds its note to the arpeggio. The key doesn't play a note itself.
3 Sequencer recording and playing Records its note into the pattern, and plays it.
4 In the sequencer, otherwise Enters its note into the selected step, and plays it.

The key LEDs light while a key is held. While the sequencer plays, the key of the current step's note lights too. While SAVE or SEL is held, the LEDs show which keys hold a saved preset or pattern.

Button combinations

# Combination What it does
1 Hold HOME, press EDIT Opens the system settings. See Settings.
2 Hold SAVE, press a key Stores the preset (in the sequencer: the pattern) on that key.
3 Hold SEL, press a key Loads the preset (in the sequencer: the pattern) from that key.
4 Hold SAVE alone for 2 seconds Saves the session, which comes back at power-on.
5 Hold OCT− and OCT+ for 5 seconds Switches to the ROM bootloader for recovery tools. See Start the ROM bootloader.
6 Hold OCT− while switching on Opens USB rescue. See If something goes wrong.