Contents

Audio

The SF1 plays in stereo through whatever output iOS has chosen, or through outputs you pick on an audio interface. It can also take audio in from the microphone or an interface. This chapter covers the output level, choosing outputs, the audio input, latency, and playing in the background or alongside other apps.

The output level

The Output module is the end of every patch. Connect the last module of each sound to it. Its AMP page has three knobs:

# Knob Range What it does
1 Volume 0 to 100 The output level.
2 Drive 0 to 100 Soft saturation on the output. At 0 it's off.
3 Tone 0 to 100 Brightness. At 100 nothing is taken off. Turning it down rolls off the highs, down to a gentle low-pass at 800 Hz at 0.

All three are saved with the patch.

The meter right of the bay shows the output level on a decibel scale. It jumps up to a peak at once and falls back slowly; a thin line holds the highest peak for a moment.

A limiter after the volume catches peaks, so a patch that's too loud gets squashed rather than distorted. The output also carries a faint hiss.

Choose the output

By default the SF1 plays wherever iOS sends sound: the speaker, headphones, AirPods, an audio interface. To pick outputs yourself:

  1. Tap the Output module in the bay.
  2. Press OUT on the programmer.
  3. Turn Output to the port you want. AUTO leaves the choice to iOS.
  4. To play the same sound on a second port at the same time, turn Out 2 to it. OFF uses only one.
# Knob Choices
1 Output AUTO, then each output port by name, for example SPEAKER or the name of your interface
2 Out 2 OFF, then each output port by name

The outputs are a device setting, not part of the patch: they stay as they are whichever patch you load.

The SF1 always sends a stereo pair. On a port with more than two channels, it plays on the first two and leaves the others silent.

While a port is picked on either knob, Bluetooth outputs can't be used. To play through Bluetooth headphones or speakers, set Output to AUTO and Out 2 to OFF.

When you plug an interface in or out, the SF1 switches over and carries on. If you unplug a port you picked, set Output back to AUTO; see No sound.

Play audio in

The Audio In module plays the device's audio input through the synth: the built-in microphone, a headset, or an input of an interface. Connect it to effects and the Output like any other source.

The first time you put an Audio In module in the bay, iOS asks for access to the microphone. If you refuse, or the device has no input, the module's picture reads NO MICROPHONE ACCESS. To allow access later, go to Settings > Privacy & Security > Microphone and switch Steckfeld SF1 on.

The module's INPUT page:

# Knob Choices What it does
1 Level 0 to 100 The input's level into the patch.
2 Input AUTO, then each input port by name Which input to use. AUTO leaves it to iOS.
3 Channel 1, 2, … then 1+2, 3+4, … Which channel of the input to take. A pair such as 1+2 is summed into one.

The synth takes the input in mono.

The input is only open while there is an Audio In module in the bay. With one in the bay, iOS shows the microphone indicator.

Latency

LATENCY on the service menu's AUDIO page sets how quickly the SF1 answers keys and knobs: 64, 128, 256 or 512. Lower values answer faster but need more processing power. If you hear crackles, pick a higher one. The default is 256, about 5 ms.

Some outputs, Bluetooth in particular, add their own delay on top.

Play in the background

BACKGROUND on the AUDIO page decides what happens to the sound when you leave the app:

# Setting What happens
1 OFF The sound stops as soon as you leave.
2 PLAY The sound keeps going while the transport runs. With the transport stopped, it stops. The default.
3 ALL The sound always keeps going, so MIDI from other apps or gear still plays the SF1 with the transport stopped.

Under PLAY, notes you play from a keyboard while the transport is stopped are not heard once you leave the app. Use ALL to play the SF1 from another app.

Mix with other apps

MIX WITH APPS on the AUDIO page decides whether the SF1 plays together with other apps' audio.

  • OFF: starting the SF1's audio stops music or sound from other apps. The default.
  • ON: the SF1 plays alongside them.

Advanced

For when you know the basics. You don't need this to get started. Skip to The terminal and the crews

Expect a short gap when the audio setup changes

The sound drops out for a moment when:

  • you put the first Audio In module into the bay, or take the last one out,
  • you pick a port on Output or Out 2 while both are on AUTO and OFF, or set them back,
  • you change MIX WITH APPS in the service menu.

Do these before you play, not during a take.

Talk through the SF1

Put an Audio In module and COMBINÉ in the bay and connect Audio In to COMBINÉ as its Voice. Connect a source playing a held chord into COMBINÉ, set that connection's Dest to Carrier, and turn COMBINÉ's Tone down towards 0. You hear the chord, shaped by your voice. COMBINÉ needs its ROM from LIGNE's board; see Crew modules.