Contents

Troubleshooting

This chapter lists common problems with the SF1 and what to check for each, starting with sound, then MIDI and clock, the bay, and buying. Each answer links to the chapter that explains the part involved.

No sound

Check these in order:

  1. Is something playing notes? A patch only sounds when notes reach a source: from a MIDI keyboard through MIDI In, or from a sequencer or arpeggiator while the transport runs. Press ▶, or play a key. See Play from a MIDI keyboard.
  2. Does the sound reach the Output? Put the parts display on PATCH, focus the Output with ◀ and ▶, and check that a connection comes in. See The patch map.
  3. Is the volume up? Tap the Output module and check Volume on its AMP page.
  4. Where does the sound go? On the Output's OUT page, set Output to AUTO and Out 2 to OFF, so iOS decides. If you unplugged a port you had picked, turn Output to another port and back to AUTO. See Choose the output.
  5. Is the device's volume up? The SF1 follows the iOS volume buttons.

If text appears on the name plate at the top of the casing, the app couldn't start its audio engine. The text is iOS's reason. Close the app fully and open it again.

Stuck notes

Tap the Output module and press PANIC on the programmer. It sends all notes off on all 16 channels.

If notes keep hanging on a keyboard with a sustain pedal, check the pedal. The SF1 holds notes while the pedal is down, so a pedal with reversed polarity holds them while it's up. Switch the polarity on the pedal or in the keyboard's settings.

Crackles or dropouts

Set LATENCY in the service menu to a larger value, such as 512. Large patches with many voices or heavy effects need a higher setting. See Latency.

The sound stops when I leave the app

Set BACKGROUND in the service menu to ALL. Under the default PLAY, the sound only keeps going while the transport runs. See Play in the background.

Music from another app stops when the SF1 starts

Set MIX WITH APPS in the service menu to ON.

Bluetooth headphones are silent

A port picked on the Output's OUT page puts the SF1 on the wired outputs only. Set Output to AUTO and Out 2 to OFF.

My keyboard doesn't play the SF1

  1. Open the service menu and go to the MIDI page. Play a key. If the heading doesn't show IN, no MIDI reaches the app: check the cable or interface, pair Bluetooth gear with BLUETOOTH, or switch NETWORK on for network MIDI.
  2. If MIDI arrives, tap the MIDI In module and check Channel. Set it to ALL to rule it out.
  3. Check that MIDI In is connected to a source, or to a Chord, Arp or Sequencer that is. See Play from a MIDI keyboard.
  4. For network MIDI and Ableton Link, allow local network access for Steckfeld SF1 in Settings > Privacy & Security > Local Network.

The sequencer doesn't start

  • Press ▶. The key stays down and lit while the transport runs.
  • With SOURCE on EXT, the SF1 waits for MIDI clock. Set it to AUTO to run on its own tempo when no clock comes in.
  • With SOURCE on LINK and FOLLOW START on, the transport is shared: another app in the session may have stopped it.

The tempo can't be changed

While the SF1 follows MIDI clock, the tempo knob reads MIDI Clock and can't be turned. Change the tempo on the sending gear, or set SOURCE to INT.

A part won't go into the bay

  • The parts display shows OUT beside it: you already have the most of that part the bay takes, four of most, one Macro.
  • No slot is free for its width. A slot under a connection doesn't count as free, because modules can't sit on a connection. Make room or move a connection.

Two modules won't connect

They must be in line, with nothing but empty slots between them, and the second module must accept what the first puts out. A connection also can't run on top of another one in the same direction or close a loop. See When two modules can connect.

A module lost its connections

Moving a module to another slot ends all its connections. Dropping it back on its own slot keeps them. See Move a module.

The programmer doesn't come in

If an FM-1 is connected and set to OPEN: Never, the programmer stays away. Change the setting on the FM-1, or disconnect it. See The FM-1 as a remote.

The controller's knobs don't move the programmer

  • The programmer must be out. Tap a module.
  • Check LEARN KNOBS in the service menu: it shows how many knobs are learned, for example 4/4.
  • If a knob jumps or barely moves, KNOBS doesn't match your controller. Knobs with end stops want ABS, endless encoders REL or REL-ACC. See Pick how the controller's knobs work.

Audio In is silent

If the module's picture reads NO MICROPHONE ACCESS, allow the microphone for Steckfeld SF1 in Settings > Privacy & Security > Microphone, or connect an input. Then check Input, Channel and Level on the module.

A crew module isn't in the parts tray

Download its ROM from the crew's board on the terminal. After reinstalling the app, download it again. See The terminal and the crews.

The bay keeps going back to SLOW CURRENT

The SF1 isn't bought on this device yet, or the purchase hasn't been restored. The demo unit loads SLOW CURRENT every time you come back to the app. Tap the price label and then RESTORE if you bought it before. See Buy the SF1.

The bill says THE STORE DOES NOT ANSWER

The app couldn't get the price from the App Store. Check the internet connection and that you're signed in to the App Store, then tap RESTORE on the bill: it asks the store again. If that doesn't help, close the app fully and open it again.

The screen goes dark while I play

The SF1 keeps the screen on while the transport runs or an FM-1 is connected. When you only play from a MIDI keyboard with the transport stopped, iOS Auto-Lock applies. Start the transport, or change Auto-Lock in Settings > Display & Brightness.

Start over

To empty the bay, press NEW on the terminal. There is no way to reset the library or the service menu from inside the app. Deleting and reinstalling the app resets everything kept on the device: the library, the settings, downloaded ROMs and the wear of the casing. Purchases come back with RESTORE.