Chorus, delay, reverb and grain
These four effects work with time: the Chorus (which also does flanging and phasing), the Delay, the Reverb and Grain, which plays a cloud of short slices from the last few seconds of audio. Each takes audio in on one connection and puts stereo audio out, with its own dry/wet mix; a patch can hold up to four of each. They are on the EFFECTS page of the parts display, with the effects in Filter, EQ, compressor and distortion. Percent controls read 0 to 100 on the display.
Control inputs
An LFO, an Envelope or the mod wheel of a MIDI In module can be connected to move one setting:
| # | Effect | Destination |
|---|---|---|
| 1 | Chorus | Depth |
| 2 | Delay | Mix |
| 3 | Reverb | Mix |
| 4 | Grain | Position |
See How control connections scale.
Chorus
A short modulated delay for chorus and flanging, or a chain of allpass filters for phasing. The two sides are swept a quarter cycle apart, which widens the sound.
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Main | Mode | CHORUS, FLANGE, PHASER | CHORUS | Type of effect. |
| 2 | Main | Rate | 0.05 Hz – 10.0 Hz | 0.80 Hz | Speed of the sweep. |
| 3 | Main | Depth | 0–100 | 50 | How far it sweeps. |
| 4 | Main | Mix | 0–100 | 50 | Dry at 0, only the effect at 100. |
| 5 | Regen | Feedback | 0–90 | 0 | How much of the effect is fed back in. Makes flanging and phasing sharper. |
| # | Mode | What it does |
|---|---|---|
| 1 | CHORUS | A delay of 15 ms swung up to 7 ms either way at full Depth. |
| 2 | FLANGE | A delay of 3 ms swung up to 2.5 ms either way. |
| 3 | PHASER | Four allpass stages per side around 700 Hz, swept up to 2.5 octaves each way. |
The effect is darker than the dry sound: everything above 8 kHz is rolled off. Switching mode or turning Depth glides over about 40 ms instead of clicking.
Delay
A stereo delay with free or clock-synced time, filters and saturation on the repeats, tape-like wow, three ways of placing the repeats in stereo, and a freeze key that loops what is in the line.
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Delay | Mode | FREE, SYNC | FREE | FREE sets the time in seconds; SYNC locks it to the clock. |
| 2 | Delay | Time | 20 ms – 2.00 s | 375 ms | Time between repeats, in FREE. |
| 3 | Delay | Sync | 1/2, 1/4, 1/4D, 1/4T, 1/8, 1/8D, 1/8T, 1/16, 1/16T, 1/32 | 1/8 | Time between repeats as a note length, in SYNC. Takes Time's place. D is dotted, T a triplet. |
| 4 | Delay | Feedback | 0–95 | 40 | How much of each repeat comes round again. |
| 5 | Delay | Mix | 0–100 | 35 | Dry at 0, only the repeats at 100. |
| 6 | Tone | Low Cut | 20 Hz – 2.0 kHz | 20 Hz | Takes the lows off the repeats. |
| 7 | Tone | High Cut | 500 Hz – 18.0 kHz | 6.0 kHz | Takes the highs off the repeats, so each one is darker. |
| 8 | Tone | Drive | 0–100 | 50 | How readily hot repeats saturate. |
| 9 | Tone | Wow | 0–100 | 0 | Slow pitch drift of the repeats, as on tape. |
| 10 | Stereo | Mode | STEREO, PING, CROSS | STEREO | How the repeats sit left and right. |
| 11 | Stereo | Spread | 0–100 | 0 | Makes the right side repeat later, up to half a delay time later at 100. |
| # | Stereo mode | What it does |
|---|---|---|
| 1 | STEREO | Each side repeats itself. |
| 2 | PING | Both sides go in on the left; the repeats bounce from side to side. |
| 3 | CROSS | Each side goes in on its own side; the repeats swap sides each time. |
FREEZE is the fifth key under the display while the Delay is on the programmer. With it on, the delay stops taking in new sound and loops what is in the line without it wearing down. It fades in and out over about 10 ms. Freeze is played, not stored: a patch never loads with the delay frozen.
In SYNC the time follows the tempo, including MIDI clock and Ableton Link. Changing Time or Sync glides the delay over about 40 ms, so the repeats bend in pitch rather than jump.
Reverb
A stereo reverb. Size sets how big the room is, Decay how long the tail lasts, independently of each other. Damping, a low cut, pre-delay, modulation, shimmer and freeze shape the tail.
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Room | Size | 0–100 | 50 | How big the room is: how far apart the echoes inside the tail are. Turning it doesn't change how long the tail lasts. |
| 2 | Room | Decay | 200 ms – 20.0 s | about 1.2 s | Time for the tail to fall 60 dB. |
| 3 | Room | Predelay | 0 – 250 ms | 10 ms | Gap before the tail starts. |
| 4 | Room | Mix | 0–100 | 35 | Dry at 0, only the reverb at 100. |
| 5 | Tone | Damping | 0–100 | 40 | How much faster the highs die away than the rest. |
| 6 | Tone | Low Cut | 20 Hz – 1.0 kHz | 100 Hz | Below it the input stays out of the tail, so the bass stays dry. |
| 7 | Tail | Mod | 0–100 | 25 | Gently moves the tail. Smooths out metallic ringing. |
| 8 | Tail | Shimmer | 0–100 | 0 | How much of the tail climbs an octave each time round. |
| 9 | Tail | Freeze | OFF, ON | OFF | Holds the tail as it is and lets nothing new in. |
Patches saved before Decay existed get a decay worked out from their Size, so they sound as they did. Unlike the Delay's freeze, the Reverb's Freeze is saved with the patch.
Grain
Records the last six seconds of what comes in and plays them back as a cloud of short, overlapping grains. Position picks where in those six seconds the grains start, Size how long each is, Density how many start per second, and Spray how far they scatter. Freeze stops recording, so the cloud plays from what the buffer already holds.
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Grain | Position | 0–100 | 50 | Where grains start: 0 the oldest audio in the buffer, 100 the newest. |
| 2 | Grain | Size | 10 ms – 1.00 s | 200 ms | Length of each grain. |
| 3 | Grain | Density | 0.5/s – 100/s | 12/s | Grains started per second. |
| 4 | Grain | Pitch | −24 to +24 st | 0 st | Plays every grain faster or slower, in semitones. |
| 5 | Cloud | Freeze | OFF, ON | OFF | Stops recording. |
| 6 | Cloud | Spray | 0–100 | 10 | Scatters each grain's start, up to a second either way at 100. |
| 7 | Cloud | Mix | 0–100 | 50 | Dry at 0, only the grains at 100. |
Up to 32 grains play at once; when all are busy, a new grain waits. Each grain leans a little to one side at random, and grains start slightly off the beat of Density, so a dense cloud doesn't buzz at the density as a pitch.
The display draws the buffer as a level graph, oldest on the left, and each grain playing as a mark at its place.
Advanced
For when you know the basics. You don't need this to get started. Skip to MIDI In, sequencer, arp and chord
Loop a phrase with the Delay
- Set the Delay's Mix to around 50 and Time to the length of the loop you want, up to 2 seconds, or SYNC it to 1/2.
- Play a short phrase.
- Press FREEZE. The phrase now loops without fading, and new notes play dry over it.
- Press FREEZE again to let the loop fade out with the feedback.
FREEZE is not saved, so set it up again after loading the patch.
Bend the repeats
Turn Time while repeats are playing and they bend up or down in pitch. Wow at 30 to 60 adds a slow wobble to every repeat. For darker, dub-style repeats, set High Cut around 2 kHz, Feedback around 70 and Drive above 60.
Endless pads with the Reverb
Set Mix to 60 or more, set Decay long, play a chord, and switch Freeze to ON. The tail holds as it is and new notes stay out of it, so you can play dry over a held pad. Set Freeze back to OFF to let it fade. Shimmer with a long Decay makes the tail climb in octaves as it fades; it stops climbing while frozen.
Scan a frozen Grain buffer
- Play or feed in some sound, then set Freeze to ON.
- Connect an LFO into the Grain; Dest is Position.
- Leave Position at 50 and set a slow LFO, such as TRI at 0.1 Hz, with a Depth around 40.
The grains wander back and forth through the held six seconds. Short grains under 50 ms sound rough and grainy; grains over 500 ms with a low Density overlap into slow smears. Pitch at −12 or +12 st with Freeze ON makes an octave-shifted texture of what was played.