Contents

MIDI In, sequencer, arp and chord

These four utilities decide which notes the sources play. MIDI In turns a keyboard or controller into notes, the Sequencer plays a pattern of up to 32 steps, the Arp plays the keys you hold one after another, and Chord turns every note it passes on into a chord. All of them put out a control signal and reach a source over a connection set to Note + Gate. They are on the UTILITIES page of the parts display; a patch can hold up to four of each. Percent controls read 0 to 100 on the display.

What plugs into what

# From Into What it does
1 MIDI In a source Plays it from the keyboard.
2 MIDI In Sequencer A held key runs the pattern, transposed.
3 MIDI In Arp The keys held are what it plays.
4 MIDI In Chord Each key becomes a chord on the sources the Chord feeds.
5 Sequencer a source, or Chord Plays the pattern.
6 Arp a source, or Chord Plays the arpeggio.
7 Chord a source Plays the chords.
8 MIDI In any control destination Sends the mod wheel, like an LFO would.

A Chord can't feed another Chord. Sources are listed in Sources and Crew modules.

When a source has more than one of these connected, a Sequencer wins over an Arp, an Arp over what plays a Chord in front of it, and all of them over MIDI In.

MIDI In

Your keyboard or controller; how to connect one is in Connect MIDI gear. One MIDI In is in every patch and can't be taken out; you can add up to three more, for example to play different sources from different channels.

# Page Knob Range Default What it does
1 MIDI Channel ALL, 1–16 ALL Which MIDI channel it listens to.
2 MIDI Bend +0 to +24 st +2 st Pitch bend range, up and down.

It understands:

# Message What it does
1 Note on and off Plays and releases notes, with velocity.
2 Pitch bend Bends every note it plays, by up to Bend semitones.
3 CC 1 (mod wheel) Sent down any control connection from MIDI In that isn't set to Note + Gate.
4 CC 64 (sustain pedal) Holds notes after their keys are let go.
5 CC 120, CC 123 All notes off.

Each source connected to the same MIDI In plays the same notes, so several sources layer. Each uses as many voices as its own Voices setting allows. With one voice a source plays the last key pressed; with more, a held note that lost its voice to a newer one gets it back when a key is let go. A key pressed again reuses its voice and starts its envelope over.

MIDI clock, start and stop arrive through MIDI In too; how the device follows them is in Clock source.

Sequencer

A step sequencer of up to 32 steps. Each step has a note, a length (a quarter to a whole step, or tied into the next), a velocity and up to four repeats. It runs on the transport; a key held on a MIDI In connected to it runs it transposed instead.

# Page Knob Range Default What it does
1 Pattern Rate 1/4, 1/8, 1/8T, 1/16, 1/16T, 1/32 1/16 Length of one step.
2 Pattern Length 8, 16, 24, 32 16 Steps before the pattern comes round.
3 Pattern Base C1 – C7 D4 The key that plays the pattern as written. Other keys from MIDI In transpose it by their distance from Base.
4 Pattern Mutate 0–100 0 Chance, each time the pattern comes round, that a step swaps its note with another step.
5 Steps Note C1 – C6 per step Note of the step under the cursor.
6 Steps Length 1/4, 2/4, 3/4, TIE 2/4 How much of the step the note sounds. TIE holds it into the next step.
7 Steps Velocity 0–100 100 How hard the step is played.
8 Steps Repeat 1×–4× 1× Hits the step that many times within its length.

Rate, and the Arp's Step, are note lengths at the device's tempo: 1/4 is one beat, 1/8 half a beat, 1/8T a third, 1/16 a quarter, 1/16T a sixth and 1/32 an eighth of a beat.

Below the display, the keys on the Sequencer's screen are:

# Key What it does
1 PATTERN Shows the Pattern page.
2 STEPS Shows the Steps page.
3 PREV Moves the step cursor back one step, wrapping round, and shows the Steps page.
4 NEXT Moves it on one step.
5 ON Switches the step under the cursor on or off. Lit while it is on.

Ties. A step set to TIE keeps the gate open into the next step. If that step is on, its note takes over without the gate closing, so envelopes don't start again and the pitch moves over.

Repeats divide the step evenly. With Length below TIE each hit sounds for that share of its own slice.

Mutate only ever swaps notes between steps that are on, so the pattern keeps its rhythm and its set of notes. The swaps build up while the transport runs; stopping it, or editing a step, puts the pattern back as written. The steps on the display show the notes as they play now.

Keyed. With a MIDI In connected to the sequencer, holding a key starts the pattern from its first step at the device's tempo, whether the transport runs or not, transposed by the key's distance from Base. Letting go stops it, or hands it back to the transport if that is running.

When the transport stops, the gate closes and the pattern goes back to its first step.

A new Sequencer comes with a 16-step bass line around A1. Patches saved with shorter patterns are padded to 32 steps with steps that are off.

Arp

An arpeggiator: it plays the keys held on the MIDI In connected to it, one after another, over up to four octaves.

# Page Knob Range Default What it does
1 Arp Mode UP, DOWN, UP/DN, PLAYED, RANDOM UP Order of the notes.
2 Arp Step 1/4, 1/8, 1/8T, 1/16, 1/16T, 1/32 1/16 Length of one note.
3 Arp Octaves 1–4 1 How many octaves the held keys are repeated over, going up.
4 Arp Gate 5–100 50 How much of the step each note sounds. 100 ties the notes together.
# Mode Order
1 UP Lowest to highest.
2 DOWN Highest to lowest.
3 UP/DN Up and back down, the top and bottom notes played once per round trip.
4 PLAYED In the order the keys were pressed.
5 RANDOM Any held note, at random.

The first key pressed sounds at once; the next note waits for the grid. While the transport runs the arp follows the clock; while it is stopped it keeps its own time at the device's tempo. Pitch bend from MIDI In bends the arpeggio. Letting go of every key stops it and starts the order over.

Chord

Sits between whatever plays a source and the source, and turns every note it passes on into a chord. Connect a MIDI In, Sequencer or Arp into the Chord, and the Chord into one or more sources.

# Page Knob Range Default What it does
1 Chord Chord OFF, 5TH, OCT, MINOR, MAJOR, SUS4, MIN7, MAJ7 OFF What is stacked on each note.
# Chord Semitones above the note played
1 OFF 0
2 5TH 0, 7
3 OCT 0, 12
4 MINOR 0, 3, 7
5 MAJOR 0, 4, 7
6 SUS4 0, 5, 7
7 MIN7 0, 3, 7, 10
8 MAJ7 0, 4, 7, 11

The chord is built from the source's own voices. A source with 7 voices playing MAJOR from a keyboard takes three voices per key, so it plays two keys at once. A chord with more notes than the source has voices loses its top notes.

Advanced

For when you know the basics. You don't need this to get started. Skip to LFO and envelope

Legato lines

Set a step's Length to TIE and the next step plays without the gate closing: its envelope doesn't start over and only the pitch moves. Tie a few steps in a row for a smooth phrase between short, plucked ones. On SCHLIERE, tied notes smear into each other.

Rolls

Set a step's Repeat to 3× or 4× and its Length to 1/4 for a quick roll within one step. Lower its Velocity for a softer roll.

Patterns that change on their own

Set Mutate between 10 and 30. Each time the pattern comes round, a few notes trade places while the rhythm stays. Stop the transport to get the pattern back as written. At 100 the notes reshuffle every round.

Arpeggiate chords

Connect MIDI In into an Arp, the Arp into a Chord, and the Chord into a source. Every note the Arp plays becomes a chord, so holding two keys with Chord on MAJOR plays two major chords in turn. Set the source's Voices to at least the number of notes in the chord.

Two sounds from two channels

Add a second MIDI In and set the two to different Channel numbers. Connect each to its own source, then send your keyboard or app on both channels, or play each from a different controller.