Contents

The programmer

The programmer is the handheld unit you edit modules with. It has one large display, four knobs standing through the glass, five keys and an E/R rocker. This chapter covers how to bring it in, how its knobs and keys work, and how to route connections on it. What each module's pages hold is in the module reference, starting with Sources.

Bring it in and put it away

Tap a module in the bay. The programmer swings up from the bottom of the screen showing that module, and the module becomes the selected one.

To put it away, tap anywhere beside it, or throw it down past the bottom edge of the screen.

You can move it while you work: drag it by its housing to anywhere in the window. It stays where you left it until you throw it out. On a narrow screen it's scaled down to fit.

While an FM-1 set to OPEN: Never is connected, the programmer doesn't come in at all. See The FM-1 as a remote.

The display

From top to bottom the display shows:

  1. The module's name, for example FILTER or DELAY 2, and on the right EDIT or ROUTE for the screen you're on.
  2. A picture of what the module does: the waveform, the filter curve, the envelope, the sequencer's steps.
  3. The four knobs, each with a ring, a label and the current value.
  4. Along the bottom edge, a label for each of the five keys under the display.

The keys themselves are blank. What a key does is whatever the display prints above it. A key with no label does nothing.

The programmer always shows the selected module. With no module selected, it shows the Output. Switching to another module goes back to its first page, and on a sequencer to step 1.

Values on screen

# Format Example Used for
1 Plain number 72 Levels and amounts, 0 to 100.
2 Semitones +7 st Tuning and bend range.
3 Cents -12 ct Fine tuning.
4 Hertz 440 Hz, 1.2 kHz, 0.50 Hz Frequencies and rates.
5 Seconds 250 ms, 1.20 s Times. Below one second in milliseconds.
6 Decibels +3.0 dB Gains.
7 BPM 120 BPM Tempo.
8 Ratio 2.00 Frequency ratios.
9 Choice SAW, BLEND Stepped choices.

A very slow rate below 0.1 Hz shows as the time one cycle takes, such as 20 s or 1.5 min.

Turn a knob

Drag a knob up or to the right to turn the value up, down or to the left to turn it down. Your finger turns every knob at the same rate: about 220 points of travel for a knob's full sweep. You can start the drag anywhere on the knob or just around it.

The ring on the display shows where the value is:

# Marking Meaning
1 Dim track The knob's full range.
2 Bright arc The value, from the start of the range. At the very bottom it's a lit dot.
3 Ticks outside the track The positions of a stepped knob with 13 positions or fewer.
4 No ring, label — Nothing on this knob on this page.

A stepped knob with up to nine positions, like a waveform choice, turns 30° per position like a rotary switch, so a short drag is enough to change it. Other knobs sweep 270°. Many frequency and time knobs change slowly at the bottom of their range and faster towards the top, so low values are easy to set finely.

The knob's cap turns with your finger past the ends of the range. The ring is the only limit. With KEY CLICKS on in the service menu, the knob clicks at each step.

When a connection moves the value

When a control connection modulates a value, such as an LFO into a filter's cutoff, its ring shows two arcs: a dim one for the value you set and a brighter one for where the engine has it right now. A short tick outside the track marks the value you set. The picture also gets a faint ghost showing the module as it plays at this moment.

Pages and keys

Most modules have more controls than four knobs can hold, so they come in pages. Each page has its own key, labelled with its name, for example OSC, PLAY and SHAPE on the Analog oscillator. Press a page key to show its knobs. The key for the page on show stays down and lit.

Some modules use the free keys for something else:

# Module Keys What they do
1 Output PANIC Sends all notes off on all 16 MIDI channels. Use it when a note hangs.
2 Delay FREEZE Switches the delay's freeze on and off. Lit while on. See Delay.
3 Sequencer PREV, NEXT, ON Move the step cursor, switch the step under it on or off.
4 Macro ARM, WRITE, CLEAR Take down a snapshot of the rack for a macro step. See Macro.

The Output module has three pages: AMP with Volume, Drive and Tone, OUT with the audio outputs (see Audio), and CLOCK with the tempo (see Tempo).

Route a connection

Push the rocker to R to switch to the route screen. Push it to E to go back to editing. A newly opened programmer always starts on E.

The route screen lists every module the selected module could be connected to, in the order they sit in the bay, row by row from the top left. A module is listed if it is in line with nothing in between, and a connection between the two would be allowed one way or the other. Each line reads like LFO ››› Filter CV · CUTOFF: this module, the direction, the other module, the kind of signal (AUDIO or CV) and the input it goes into. The small square at the start of a line is lit when the connection is on.

If no module is in line, the screen reads NOTHING IN SIGHT.

# Key What it does
1 PREV Selects the line above. Shown when there is more than one line.
2 NEXT Selects the line below.
3 FLIP Reverses the direction. On a connection that's on, it reconnects the other way round and keeps its amount. On one that's off, it only changes which way it would run. Shown when both directions are possible.
4 ON Switches the selected connection on or off. Lit while on.

While the selected connection is on, the knobs show its CABLE page:

# Knob Range What it does
1 Dest Depends on the pair Which input on the receiving module the connection drives, for example Cutoff, Resonance or Morph on a Filter. Only shown when there's more than one choice.
2 Level 0 to 100 How much of the audio goes through. Audio connections only.
3 Depth 0 to 100 How strongly the control signal moves the destination. Control connections only.

A Note + Gate connection, which plays a source, has no amount knob.

Crew firmware

The four crew modules (ДАМП, 曲げ MAGE, SCHLIERE, COMBINÉ) and the Macro run firmware written by one of the crews. When the programmer shows one of them, the crew's firmware takes over its display: a black screen with the crew's art behind the knobs, text in a console font, and the crew's colours.

# Crew Colours
1 СЕКТОР Grey
2 LIGNE Minitel cyan, with a 3615 tag and a blue, white and red bar under the module's name
3 RASTER Gold
4 回路 KAIRO Neon pink

The controls work as on any other module. See The terminal and the crews.

Turn the knobs from a MIDI controller

The four knobs can follow four knobs or encoders on a MIDI controller while the programmer is out. Set this up with LEARN KNOBS and KNOBS in the service menu. See Control the programmer from MIDI.

Advanced

For when you know the basics. You don't need this to get started. Skip to Patches and the library

Reverse a connection and keep its amount

On the route screen, select the connection and press FLIP. It's reconnected the other way round and keeps its Level or Depth; Dest goes back to the first input in the list. Disconnecting and swiping it the other way in the bay would also reset the amount to 100.