MIDI and clock
The SF1 has no keyboard of its own. You play it from MIDI gear or another app, and it can run on its own clock, follow MIDI clock or join an Ableton Link session. This chapter covers connecting MIDI gear, playing notes, the transport and tempo, clock sync, turning the programmer's knobs from a controller, and using an M-VAVE FM-1 as a remote.
Connect MIDI gear
The SF1 listens to every MIDI port on the device at once. You don't pick a port.
| # | Connection | What to do |
|---|---|---|
| 1 | USB keyboard or controller | Plug it in. It's heard right away. |
| 2 | 5-pin DIN gear | Connect it through a USB MIDI interface. |
| 3 | Bluetooth MIDI | Pair it from the service menu, see below. Once paired, it's heard like any other port. |
| 4 | Network MIDI | Switch NETWORK on in the service menu, then connect from the other computer or device. |
| 5 | Another app on the device | Send to the port called Steckfeld. |
Pair Bluetooth MIDI gear
- Press SVC.
- Press ▼ until BLUETOOTH is highlighted. It's on the MIDI page.
- Press OK. Apple's Bluetooth MIDI screen opens.
- Pick your device and pair it, then close the screen.
Network MIDI
With NETWORK set to ON, the SF1 accepts network MIDI sessions from anyone on your local network. iOS asks once for permission to use the local network; allow it. Set NETWORK to OFF to stop accepting sessions.
See whether MIDI arrives
On the service menu's MIDI page, the heading shows IN while MIDI messages are arriving, or the last controller message, such as CC74 64. The MIDI In module's picture on the programmer lights up as well.
Play from a MIDI keyboard
Notes reach the sound sources through the MIDI In module. Every patch has one. A source plays when a control connection runs from MIDI In into it with the destination Note + Gate.
To play a patch from a keyboard:
- Check that MIDI In is connected to the source you want to hear, or to a Chord module, arpeggiator or sequencer in front of it. The patch map shows this. See The patch map.
- Play.
If more than one source is connected to the same MIDI In, they play together, layered.
How many notes a source plays at once is set with Voices on the source's PLAY page, from 1 to 7. With one voice, the latest key wins and a released key hands the voice back to a key still held.
The MIDI In module has two knobs. More on it in MIDI In.
| # | Knob | Range | What it does |
|---|---|---|---|
| 1 | Channel | ALL, 1 to 16 | Which MIDI channel it listens to. ALL takes every channel. |
| 2 | Bend | +0 to +24 st | How far the pitch bend wheel bends, up and down. |
The sustain pedal (CC 64) holds notes until you lift it. The mod wheel (CC 1) is what MIDI In sends down a control connection that isn't Note + Gate, for example into a source's Pitch or Width.
You can have up to four MIDI In modules, each on its own channel, to play different parts of a patch from different keyboards or channels.
The transport
The ▶ key on the keypad starts and stops the transport. It stays down and lit while the transport runs. The transport runs the sequencers, arpeggiators and everything synced to the clock.
A sequencer connected from MIDI In also starts from a key, with the transport stopped. See Sequencer.
With FOLLOW START on, MIDI Start, Continue and Stop from your gear start and stop the transport too. A received Start or Stop is never sent back out.
Tempo
The SF1 has one tempo for the whole device. Set it on the Output module:
- Tap the Output module in the bay.
- Press CLOCK on the programmer.
- Turn Tempo, from 40 to 240 BPM.
The tempo is saved with the patch.
While the SF1 follows MIDI clock, the knob is labelled MIDI Clock and shows the incoming tempo. It can't be turned then.
Clock source
Set where the clock comes from with SOURCE on the service menu's CLOCK page:
| # | Setting | What it does |
|---|---|---|
| 1 | AUTO | Runs on its own tempo, and follows MIDI clock whenever some arrives. The default. |
| 2 | INT | Always runs on its own tempo and ignores incoming MIDI clock. |
| 3 | EXT | Only runs on MIDI clock. Without it, synced parts wait. |
| 4 | LINK | Joins an Ableton Link session on the network. See Ableton Link. |
While the SF1 follows MIDI clock, the CLOCK page heading shows SYNC.
When MIDI clock stops for a moment under AUTO, the SF1 carries on at its own tempo.
Send clock
With SEND CLOCK on, the SF1 sends MIDI clock while its transport runs on its own tempo: a Start when you press ▶, clock while it runs, and a Stop when you press ▶ again. It sends to every MIDI port and to the Steckfeld port other apps can listen to.
It doesn't send clock while it follows someone else's: then the transport belongs to them.
SEND CLOCK is on by default.
Ableton Link
With SOURCE set to LINK, the SF1 joins the Link session on your local network and shares tempo and bar position with every Link app in it. Bars are four beats long.
- Change the tempo on the SF1 and every app in the session follows. Change it in another app and the SF1 follows.
- With FOLLOW START on, starting or stopping the transport in any app in the session starts or stops it in all of them.
- The CLOCK page heading shows LINK and how many other apps are in the session, for example LINK 2.
iOS asks once for permission to use the local network. Link needs it.
Control the programmer from MIDI
You can give the programmer's four knobs to four knobs or encoders on a MIDI controller. They then turn whatever the programmer shows, as long as it is out.
Learn the knobs
- Press SVC and press ▼ until LEARN KNOBS is highlighted.
- Press OK. Any knobs learned before are forgotten, and the value reads MOVE 1/4.
- Turn the controller knob you want for the programmer's top left knob. Then the one for the top right, then bottom left, then bottom right.
- After the fourth, learning stops by itself and the value reads 4/4.
Press OK again to stop early with fewer than four. Each controller can only be learned once.
Pick how the controller's knobs work
Set KNOBS to match what your controller sends:
| # | Setting | For | How it behaves |
|---|---|---|---|
| 1 | ABS | Knobs with a start and an end, sending 0 to 127 | The programmer's knob moves towards the controller's position, so the two meet and lock without a jump. The default. |
| 2 | REL | Endless encoders sending relative values, 1 for one click up and 127 for one click down | Each click moves the knob one step: one position on a stepped knob, a hundredth of the range on any other. |
| 3 | REL-ACC | The same encoders | Like REL, but quick turns count up to six times as much, so you can cross the range fast and still set it finely. |
Switching KNOBS, the module or the page on the programmer resets which knobs have caught up in ABS mode.
The FM-1 as a remote
An M-VAVE FM-1 running the free Fernbedienung firmware can stand in for the programmer. Connect it over USB. The SF1 finds it by itself; there's nothing to set up in the app.
The FM-1 then shows the module pages and turns them with its four encoders, shows the connections of the route screen, lists the library, and steps through macro and sequencer steps. Its keys play the SF1 like any MIDI keyboard. On the sequencer's edit screen, a key also enters its note into the step under the cursor; the same note again clears the step.
Picking a module on the SF1 always switches the FM-1 to it. Whether picking a module on the FM-1 also brings in the SF1's programmer is set on the FM-1 with OPEN. With OPEN: Never, the programmer stays away the whole time the FM-1 is connected.
While an FM-1 is connected, or while the transport runs, the screen doesn't go to sleep.
If the FM-1's own audio output is connected but the SF1 plays somewhere else, the FM-1 says so, for example Sound on iPad, and offers to switch the output to the FM-1.
If the FM-1 shows that it needs an update, install the current Fernbedienung firmware. Until then it doesn't work as a remote.
The firmware, how to install it and everything the FM-1's keys do are in the Fernbedienung manual.
Advanced
For when you know the basics. You don't need this to get started. Skip to Audio
What your MIDI gear can control
| # | Message | Effect |
|---|---|---|
| 1 | Note on and off | Played by MIDI In modules on that channel. |
| 2 | Pitch bend | Bends MIDI In's notes by its Bend range. |
| 3 | CC 1, mod wheel | Sent down MIDI In's control connections. |
| 4 | CC 64, sustain | Holds notes while 64 or higher. |
| 5 | CC 120 and 123 | All sound off and all notes off. |
| 6 | Any other CC | Only used for learned programmer knobs. |
| 7 | Clock, Start, Continue, Stop | Followed as set by SOURCE and FOLLOW START. |
Program changes and aftertouch are ignored.
Gear connected over two ports
If the same gear reaches the SF1 over two ports at once, for example USB and Bluetooth, the SF1 takes clock and transport from the port that sent them first. The other port only takes over after the first has been silent for a second.
Catch a knob in ABS mode
After you switch module or page, the controller knob and the programmer's knob usually point to different values. Turn the controller in either direction. The programmer's knob moves along at a rate that brings both to that end of the range together, so they meet there at the latest. Once they meet, or once you sweep the controller past the knob's value, the knob follows the controller directly.