Contents

LFO and envelope

The LFO and the Envelope move other modules' settings over a control connection: the LFO in a repeating cycle, the Envelope once per note. This chapter also lists how far a control connection moves each destination, which is the same for an LFO, an Envelope and the mod wheel of a MIDI In. Both modules are on the UTILITIES page of the parts display; a patch can hold up to four of each. Percent controls read 0 to 100 on the display.

LFO

A low-frequency oscillator with six waves, running free, locked to the clock, or restarted by each new note.

# Page Knob Range Default What it does
1 LFO Wave SINE, TRI, SAW, SQUARE, STEP, RANDOM SINE Shape of the cycle.
2 LFO Mode FREE, SYNC, TRIG FREE How it keeps time.
3 LFO Rate 0.005 Hz – 20 Hz 1.00 Hz Speed, in FREE and TRIG. Below 0.1 Hz it reads as the time one cycle takes, up to 3.3 min.
4 LFO Sync 32 BAR, 16 BAR, 8 BAR, 4 BAR, 2 BAR, 1 BAR, 1/2, 1/4, 1/8, 1/8T, 1/16, 1/32 1/4 Length of one cycle, in SYNC. Takes Rate's place.
5 LFO Depth 0–100 0 How far it swings.

Depth starts at 0, so a new LFO does nothing until you turn it up. Its output swings between −Depth and +Depth; the connection's own depth then scales that again.

# Wave Shape
1 SINE Smooth swing.
2 TRI Straight up and down.
3 SAW Rises, then drops back.
4 SQUARE Jumps between top and bottom, half a cycle each.
5 STEP A new random value each cycle, held until the next.
6 RANDOM Glides smoothly to a new random value each cycle.
# Mode What it does
1 FREE Runs at Rate, all the time.
2 SYNC Locked to the clock: one cycle per Sync length, starting on the beat. It follows the device's tempo, MIDI clock or Ableton Link, and stands still while the transport is stopped.
3 TRIG Runs at Rate and starts its cycle over whenever a note starts after a moment of silence.

TRIG listens to every Sequencer, Arp and MIDI In in the patch: the cycle starts over when one of them opens a gate while none had a gate open.

Envelope

An ADSR envelope with an adjustable curve. Connected to a source's Level, it shapes every note that source plays, each note with its own copy. Connected anywhere else, such as a filter's Cutoff, it is one envelope for the whole patch.

# Page Knob Range Default What it does
1 ADSR Attack 1 ms – 5.00 s 5 ms Time to rise to full.
2 ADSR Decay 1 ms – 5.00 s 200 ms Time to fall to the sustain level.
3 ADSR Sustain 0–100 60 Level held while the note is held.
4 ADSR Release 1 ms – 5.00 s 150 ms Time to fall to nothing after the note is let go.
5 Shape Curve 0–100 50 0 is straight lines, 50 the curve of an analog envelope, 100 sharper still.

At 50 the attack rises fast and slows near the top, and decay and release fall fast and then tail off. Towards 0 all three become straight lines. Turning Curve doesn't change the times.

Which notes it follows. An Envelope connected to the Level of one or more sources follows the notes of those sources. An Envelope that isn't on any source's Level follows every Sequencer, Arp and MIDI In in the patch: it opens when any of them opens a gate and releases when all of them are closed.

Several on one source. Two Envelopes on the same source's Level are blended, each weighted by its connection's depth.

How control connections scale

A control connection has a Depth of 0 to 100 (default 100), set on its CABLE page on the route screen. What the signal does at the far end depends on the destination. An LFO's signal runs between −Depth and +Depth of the LFO; an Envelope's between 0 and 1; the mod wheel's between 0 and 1. Signals from several connections into the same destination add up.

# Destination What a full signal at connection depth 100 does
1 Pitch Moves the source up one octave. An LFO swings it up to an octave either way.
2 Cutoff (Filter), Mid Freq (EQ) An LFO swings it up to 3 octaves either way; an Envelope or the mod wheel opens it up to 4 octaves.
3 Level, from an Envelope The Envelope becomes the source's amp. Below depth 100, part of the note passes at full level and the rest follows the Envelope.
4 Level, from an LFO Tremolo that dips down from full level. At LFO Depth 100 and connection depth 100 it swings all the way to silence. At LFO Depth 0 it changes nothing.
5 Level, from the mod wheel (Audio In only) Wheel down turns it down, by as much as the connection's depth.
6 Width (Analog) Moves the duty cycle up to 45 points either way.
7 Every other destination Adds the signal on top of the knob's setting, 1 counting as the whole range: Resonance, Morph, Position, Warp, Index, Feedback, Drive, Depth, Mix, Address, Bend, Blend.

The rings around the programmer's knobs, and the wavetable and filter displays, follow these connections live. The value you dialled in shows as a dimmer arc underneath.

Which destinations each module offers is listed in its own chapter: Sources, Filter, EQ, compressor and distortion, Chorus, delay, reverb and grain, Crew modules and Mixer.

Advanced

For when you know the basics. You don't need this to get started. Skip to Mixer and output

Vibrato

  1. Connect an LFO into the source and set the connection's Dest to Pitch.
  2. On the LFO, pick SINE, FREE and a Rate around 5 Hz.
  3. Set the LFO's Depth to 10 and the connection's depth to 20.

That swings the pitch about 25 cents either way. LFO Depth 100 at connection depth 100 is a full octave either way, so small values go a long way. With Mode on TRIG, every new phrase starts the vibrato at the same point of its cycle.

Random steps

Set an LFO to STEP, Mode SYNC and Sync 1/16, and connect it into a Filter. The cutoff jumps to a new random value every sixteenth note. RANDOM instead of STEP glides between the values.

Slow drift over minutes

Below 0.1 Hz the LFO's Rate reads as the time one cycle takes, up to 3.3 minutes. In SYNC, 32 BAR takes 32 bars per cycle. Use either on a Wavetable's Position or a Reverb's Mix to change a held sound over minutes.

The mod wheel as a control

Connect MIDI In into a Filter; the connection takes the mod wheel. With the wheel down the cutoff stays where it is set, and pushing it up opens the cutoff by up to 4 octaves at connection depth 100. Into a source's Pitch it bends up by as much as an octave, so lower the depth for a smaller range.