Mixer and output
The Mixer is the rack's junction: it passes a signal on, splits it, merges several, crossfades between what it merges, and takes a connection round a corner. The Output is the amp and speaker every patch ends in, with the device's tempo and output ports on its pages. The Mixer is on the UTILITIES page of the parts display; the Output is never in the parts tray, because it is already in every patch.
Mixer
A connection only runs in a straight line between two modules that are in line with each other, over empty slots and never along another connection. A Mixer is how you get round that: connect into it, and out of it in another direction. It also lets one signal reach several modules, or several signals reach one.
A Mixer has no signal of its own: it carries whatever is connected to it, audio or control, and only one kind at a time. A connection into a Mixer is set to Through; what the signal drives is chosen on the connection leaving it, as if the Mixer weren't there.
Each Mixer either splits or merges, never both: with more than one connection in it can have only one out, and with more than one out it can have only one in. Connections can't close a loop through Mixers either. A patch can hold up to 32 Mixers.
A Mixer carrying control signals adds them up and has no settings. A Mixer carrying audio has one page:
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Mixer | Mode | SUM, BLEND | SUM | SUM passes every input on at its own level. BLEND crossfades between them. |
| 2 | Mixer | Blend | 0–100 | 50 | In BLEND, where the crossfade sits. Reads SUM while Mode is SUM. |
Blend sweeps across the inputs in the order their connections were plugged in: at 0 only the first is heard, at 100 only the last, and in between the two inputs either side of the position are crossfaded at equal power. With two inputs, 50 is both at about 71%; with three, 50 is the middle input alone.
A control connection from an LFO, Envelope or MIDI In into an audio Mixer is set to Blend and moves the crossfade, adding to the Blend setting.
Output
The amp and speaker: one in every patch, never in the parts tray, and it can't be taken out. Audio connections end here. It also holds the device's tempo and picks which hardware output you hear.
| # | Page | Knob | Range | Default | What it does |
|---|---|---|---|---|---|
| 1 | Amp | Volume | 0–100 | 100 | Master volume. |
| 2 | Amp | Drive | 0–100 | 0 | Overdrives the amp. |
| 3 | Amp | Tone | 0–100 | 100 | 100 is open; turning it down blends towards a dark lowpass at 800 Hz. |
| 4 | Out | Output | AUTO, or a port by name | AUTO | Which hardware output plays the patch. AUTO leaves it to the system. |
| 5 | Out | Out 2 | OFF, or a port by name | OFF | A second hardware output that plays the same stereo mix. |
| 6 | Clock | Tempo | 40–240 BPM | 120 BPM | The device's tempo, for every sequencer, arpeggiator, synced LFO and synced delay. |
While MIDI clock is coming in, the Clock page shows MIDI Clock with the incoming tempo instead, and it can't be turned. Clock sources and Ableton Link are covered in Clock source and Ableton Link.
The Output never clips: peaks that would go over are held back. Turning Volume up past what the patch can take gets no louder instead of distorting.
The output ports are device settings, not part of the patch (see Choose the output). With a port picked, the mix goes to that port's first two channels and the rest of its channels stay silent.
PANIC is the fifth key under the display while the Output is on the programmer. It sends All Notes Off on all 16 MIDI channels, for a patch whose notes hang.
Advanced
For when you know the basics. You don't need this to get started. Skip to Crew modules
Crossfade two sources with an LFO
- Connect two sources into a Mixer and the Mixer on to the Output or an effect.
- Set the Mixer's Mode to BLEND and Blend to 50.
- Connect an LFO into the Mixer; the connection is set to Blend.
- Turn the LFO's Depth up to 50.
The sound sweeps from one source to the other and back. With an Envelope instead, Blend at 0 and connection depth 100, every note starts on the first source and moves to the second as the Envelope rises.
Reorder a Blend
Blend sweeps the inputs in the order their connections were plugged in. To move an input to the end of the sweep, take its connection out and plug it back in.